DSXchange

Hello,
i found many entries in the forum regarding this topic, but nothing for my special problem:

We change out environement from HP to AIX, and of course get Oracle new installed.

On the new maschine all jobs reading from oracle now get this messages "Column ... floating point decimal is not fully supported; adjusting the scale."

This was not the case in the old environment.

Well something must be different on the new maschine, but what?
It is a Datastage parameter,
a Unix parameter
or a Oracle paraemter ???

Hope, that anybody can help me. Thanks a lot in advance !!!
Manfred

I liked on of Ray's old posts on this subject:

ray.wurlod wrote:It's all Oracle bin Larry's fault for not having a proper Integer data type.

You can not prevent this message without adjusting your metadata precisely to match that of Oracle, and even then you will get a message logged (a slightly different one).

This is one of those alert messages that it is safe to ignore, and therefore I tend to demote it to informational using a message handler. (I never suppress messages from the log.)

Thanks for your feedback.
But this sounds like to make changes in Datastage on Job level.
As the jobs run properly in the old environment, but now i get in dozends of jobs 100s of warinings, i think there is a very general parameter issue anywhere in Datstage, Unix or Oracle which has to be changed, or?
Manfred

The recommendation remains to demote this to an informational level message as the message cannot be avoided and is generally not a valid warning.

So, in your old environment you didn't get these messages at all? If so, what's different about the Oracle environment between servers, specifically the exact Oracle client version installed in each?

Was the message suppressed on the old system and you did not migrate the message handler(s)?

Hello Ray,

well, Datastage Source have been migrated to a new system.
But not the Message-Handler.
How could i do this ???

Manfred

search for msh file which was being used for other project (should be present in installation directory and then set it as default for the project in new system.

Hello,

well, meanwhile i have manual demoted many warnings to informational on the new Test-Maschine.
I find now many ".msh" Files there:
dsuser@dwhsie1u /datastage # find . -name *.msh -print
./Ascential/DataStage/Projects/DEV_EDW/RT_SC139/Local.msh
./Ascential/DataStage/Projects/DEV_EDW/RT_SC137/Local.msh
./Ascential/DataStage/Projects/DEV_EDW/RT_SC237/Local.msh
./Ascential/DataStage/Projects/DEV_EDW/RT_SC164/Local.msh
./Ascential/DataStage/Projects/DEV_EDW/RT_SC174/Local.msh
./Ascential/DataStage/Projects/DEV_EDW/RT_SC153/Local.msh
./Ascential/DataStage/Projects/DEV_EDW/RT_SC160/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC730/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC731/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC726/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC725/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC724/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC723/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC719/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC716/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC715/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC711/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC709/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC687/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC681/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC680/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC679/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC678/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC732/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC733/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC734/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC735/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC736/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC737/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC740/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC741/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC742/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC743/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC744/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC745/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC746/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC747/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC751/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC753/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC754/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC755/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC774/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC844/Local.msh
./Ascential/DataStage/Projects/IIP_DEV/RT_SC845/Local.msh

How can i move this file to the future Produktion system???
Can i concatinate all Content to one file?
If yes, where to put this one big file?

Those are "local message handlers", they need to be in the directory for the job they are associated with and thus no "put in one giant file" option. You'd need to find the job number of the job in question and then migrate the msh file from there to whatever job number the job has in production as it will be different.

There is a patch by IBM which take care of this oracle warning and the patch number is e117761_aix_DS7511.tar
you may want to ask them about this.

Super,
thanks for the hint to the IBM patch!
Manfred