Hi,
I am trying to develop a stage using New Parallel State Build. While I tried to Generate, I am getting the below error. I understood, the error belongs to input and output port. It will be very helpful, if anyone helps me to resolve this error.
Please let me know if there is any good doc for this (Help is not sufficient!!)
Operator Generation Failed
buildop -f -BC cxx -BL cxx -FN -C buildop -H buildop -O buildop -W buildop buildop/ReadSeqFile.opd
##E TBLD 000000 Subprocess command failed with exit status 512
##I TBLD 000008 cxx -IC:/Ascential/DataStage/Projects/SampleJobs/buildop -IC:/Ascential/DataStage/PXEngine/include -W/TP -W/EHa -DAPT_USE_ANSI_IOSTREAMS -c C:/Ascential/DataStage/Projects/SampleJobs/buildop/bosource984-0.C -o /tmp/bosource984-0_s.o
##I TBLD 000000 Output from subprocess: bosource984-0.C(298) : error C2040: 'in0' : 'ReadSeqFile::runLocally::APT_Bop_input0Accessors &' differs in levels of indirection from 'ReadSeqFile::runLocally::APT_Bop_input0Accessors'
bosource984-0.C(298) : error C3861: 'in0': identifier not found, even with argument-dependent lookup
bosource984-0.C(299) : error C2040: 'out0' : 'ReadSeqFile::runLocally::APT_Bop_output0Accessors &' differs in levels of indirection from 'ReadSeqFile::runLocally::APT_Bop_output0Accessors'
bosource984-0.C(299) : error C386
##I TBLD 000000 Output from subprocess: 1: 'out0': identifier not found, even with argument-dependent lookup
bosource984-0.C(306) : error C3861: 'in0': identifier not found, even with argument-dependent lookup
bosource984-0.C(309) : error C3861: 'out0': identifier not found, even with argument-dependent lookup
Thanks in advance.
Sura
Error while Generate (Build)
Moderators: chulett, rschirm, roy
Re: Error while Generate (Build)
Hi,
Just i removed the input and output port and then Generated. I am getting the below messge.
Operator Generation Succeeded
buildop -f -BC cxx -BL cxx -FN -C buildop -H buildop -O buildop -W buildop buildop/ReadSeqFile.opd
register-library -verbose -registry buildop buildop/ReadSeqFile.dll
1 operators registered from ReadSeqFile
But when i tried to use the stage, i am getting the below error.
(40906) Unable to create the new object
Please help me to go further.
Thanks in advance.
Sura
Just i removed the input and output port and then Generated. I am getting the below messge.
Operator Generation Succeeded
buildop -f -BC cxx -BL cxx -FN -C buildop -H buildop -O buildop -W buildop buildop/ReadSeqFile.opd
register-library -verbose -registry buildop buildop/ReadSeqFile.dll
1 operators registered from ReadSeqFile
But when i tried to use the stage, i am getting the below error.
(40906) Unable to create the new object
Please help me to go further.
Thanks in advance.
Sura
Are you assigning values to the out0 structure?
I would try to do a dummy BuildOp which just duplicates the input to the output and see if you can get that to compile and run.
I would try to do a dummy BuildOp which just duplicates the input to the output and see if you can get that to compile and run.
<a href=http://www.worldcommunitygrid.org/team/ ... TZ9H4CGVP1 target="WCGWin">
</a>
</a>
Ok, then stick with the input.
The error is
The error is
What is your input schema?##I TBLD 000000 Output from subprocess: bosource984-0.C(298) : error C2040: 'in0' : 'ReadSeqFile::runLocally::APT_Bop_input0Accessors &' differs in levels of indirection from 'ReadSeqFile::runLocally::APT_Bop_input0Accessors'
<a href=http://www.worldcommunitygrid.org/team/ ... TZ9H4CGVP1 target="WCGWin">
</a>
</a>