Anyone seen an error like this ?
DataStage Job 49 Phantom 28544
File name "JOB.1182663753.DT.1236265332.V0S175.IDENT1" too long. Truncated to "JOB.1182663753.DT.1236265332.V0S175.IDENT".
DataStage Phantom Finished
regards,
Peter
Phantom Error on DS 5.1 - File name too long
By default &PH& is what UniVerse terms a "Type 1" file. In a Type 1 file, IDs are limited to 41 characters. "JOB.1182663753.DT.1236265332.V0S175.IDENT1" is 42 characters long, which is why it was truncated. To prevent recurrence, get to a UniVerse command prompt (perhaps the Command facility in the Administrator client) and execute the UniVerse command RESIZE &PH& 19. This converts &PH& to what UniVerse terms a "Type 19" file, in which there is no limit - other than the operating system limit on the length of a file name - on the length of a record ID. Then re-compile the job.
BTW, the designator V0S175 suggests that this is the 175th object added to your job design. This is a large number! (Then again, numbers are not re-used, so you may have made many changes over time to your job design.)
-----Original Message-----
From: Peter Oates [mailto:Peter.Oates@macquarie.com]
Sent: Thursday, 08 November 2001 11:52
To: datastage-users@oliver.com
Subject: Phantom Error on DS 5.1 - File name too long
Anyone seen an error like this ?
DataStage Job 49 Phantom 28544
File name "JOB.1182663753.DT.1236265332.V0S175.IDENT1" too long. Truncated to "JOB.1182663753.DT.1236265332.V0S175.IDENT".
DataStage Phantom Finished
regards,
Peter
BTW, the designator V0S175 suggests that this is the 175th object added to your job design. This is a large number! (Then again, numbers are not re-used, so you may have made many changes over time to your job design.)
-----Original Message-----
From: Peter Oates [mailto:Peter.Oates@macquarie.com]
Sent: Thursday, 08 November 2001 11:52
To: datastage-users@oliver.com
Subject: Phantom Error on DS 5.1 - File name too long
Anyone seen an error like this ?
DataStage Job 49 Phantom 28544
File name "JOB.1182663753.DT.1236265332.V0S175.IDENT1" too long. Truncated to "JOB.1182663753.DT.1236265332.V0S175.IDENT".
DataStage Phantom Finished
regards,
Peter
Ray,
Yes, lots of changes.
Apparently this is on the Ascential KnowledgeBase as a known problem to be fixed in 5.1.1. ( I should have looked there first).
Article ID G36148
regards,
Peter
-----Original Message-----
From: Ray Wurlod [mailto:ray.wurlod@Informix.Com]
Sent: Thursday, 8 November 2001 12:02 PM
To: datastage-users@oliver.com
Subject: RE: Phantom Error on DS 5.1 - File name too long
By default &PH& is what UniVerse terms a "Type 1" file. In a Type 1 file, IDs are limited to 41 characters. "JOB.1182663753.DT.1236265332.V0S175.IDENT1" is 42 characters long, which is why it was truncated. To prevent recurrence, get to a UniVerse command prompt (perhaps the Command facility in the Administrator client) and execute the UniVerse command RESIZE &PH& 19. This converts &PH& to what UniVerse terms a "Type 19" file, in which there is no limit - other than the operating system limit on the length of a file name - on the length of a record ID. Then re-compile the job.
BTW, the designator V0S175 suggests that this is the 175th object added to your job design. This is a large number! (Then again, numbers are not re-used, so you may have made many changes over time to your job design.)
-----Original Message-----
From: Peter Oates [mailto:Peter.Oates@macquarie.com]
Sent: Thursday, 08 November 2001 11:52
To: datastage-users@oliver.com
Subject: Phantom Error on DS 5.1 - File name too long
Anyone seen an error like this ?
DataStage Job 49 Phantom 28544
File name "JOB.1182663753.DT.1236265332.V0S175.IDENT1" too long. Truncated to "JOB.1182663753.DT.1236265332.V0S175.IDENT".
DataStage Phantom Finished
regards,
Peter
Yes, lots of changes.
Apparently this is on the Ascential KnowledgeBase as a known problem to be fixed in 5.1.1. ( I should have looked there first).
Article ID G36148
regards,
Peter
-----Original Message-----
From: Ray Wurlod [mailto:ray.wurlod@Informix.Com]
Sent: Thursday, 8 November 2001 12:02 PM
To: datastage-users@oliver.com
Subject: RE: Phantom Error on DS 5.1 - File name too long
By default &PH& is what UniVerse terms a "Type 1" file. In a Type 1 file, IDs are limited to 41 characters. "JOB.1182663753.DT.1236265332.V0S175.IDENT1" is 42 characters long, which is why it was truncated. To prevent recurrence, get to a UniVerse command prompt (perhaps the Command facility in the Administrator client) and execute the UniVerse command RESIZE &PH& 19. This converts &PH& to what UniVerse terms a "Type 19" file, in which there is no limit - other than the operating system limit on the length of a file name - on the length of a record ID. Then re-compile the job.
BTW, the designator V0S175 suggests that this is the 175th object added to your job design. This is a large number! (Then again, numbers are not re-used, so you may have made many changes over time to your job design.)
-----Original Message-----
From: Peter Oates [mailto:Peter.Oates@macquarie.com]
Sent: Thursday, 08 November 2001 11:52
To: datastage-users@oliver.com
Subject: Phantom Error on DS 5.1 - File name too long
Anyone seen an error like this ?
DataStage Job 49 Phantom 28544
File name "JOB.1182663753.DT.1236265332.V0S175.IDENT1" too long. Truncated to "JOB.1182663753.DT.1236265332.V0S175.IDENT".
DataStage Phantom Finished
regards,
Peter