ABAP stage didn't work due to CPI-C error
Moderators: chulett, rschirm, roy
-
- Participant
- Posts: 18
- Joined: Sun Sep 12, 2004 9:19 am
ABAP stage didn't work due to CPI-C error
Hi All,
Has any one used ABAP stage in DataStage Extract Pack for SAP R/3 to extract data from SAP? I have created an ABAP stage according to the handbook instructions. After that, I validated the stage and it's OK. But when I tried to run the job, the following error message occured:
Test2..ABAP_EXT_for_R3_0: CPI-C initialization failure
Any idea is appreciated, thanks!
Regards,
Gordon
Has any one used ABAP stage in DataStage Extract Pack for SAP R/3 to extract data from SAP? I have created an ABAP stage according to the handbook instructions. After that, I validated the stage and it's OK. But when I tried to run the job, the following error message occured:
Test2..ABAP_EXT_for_R3_0: CPI-C initialization failure
Any idea is appreciated, thanks!
Regards,
Gordon
-
- Premium Member
- Posts: 1044
- Joined: Wed Sep 29, 2004 3:30 am
- Location: Nottingham, UK
- Contact:
Re: ABAP stage didn't work due to CPI-C error
Yes, we've had this, but it was quite some time ago. I think it might have been to do with ports not being open on the DS server, I think the port number matches the SAP system number, so system number 00 communicates on port 0. I'll update this post if I think of anything else.gordonxiao wrote:Hi All,
Test2..ABAP_EXT_for_R3_0: CPI-C initialization failure
Bear in mind that when you click the "Validate" button, that's your client connecting to SAP, but when you run the job, it's the DataStage server connecting.
Phil Hibbs.
Last edited by PhilHibbs on Fri Jun 03, 2005 4:55 am, edited 1 time in total.
Phil Hibbs | Capgemini
Technical Consultant
Technical Consultant
-
- Participant
- Posts: 3337
- Joined: Mon Jan 17, 2005 4:49 am
- Location: United Kingdom
-
- Premium Member
- Posts: 353
- Joined: Wed Apr 06, 2005 8:45 am
-
- Participant
- Posts: 232
- Joined: Sat May 07, 2005 2:49 pm
- Location: USA
-
- Premium Member
- Posts: 353
- Joined: Wed Apr 06, 2005 8:45 am
-
- Participant
- Posts: 232
- Joined: Sat May 07, 2005 2:49 pm
- Location: USA
Hi Vinay,
If you are using SAP R/3 Pack to extract data from SAP 3.1. Then it will not work. It seems that the SAP R/3 pack is not compatible with SAP 3.1. However, it works well with the higher version SAP 4.7.
This problem was reported to the Ascential Support and they did confirm the incompatibility with SAP 3.1 version.
If you are using SAP R/3 Pack to extract data from SAP 3.1. Then it will not work. It seems that the SAP R/3 pack is not compatible with SAP 3.1. However, it works well with the higher version SAP 4.7.
This problem was reported to the Ascential Support and they did confirm the incompatibility with SAP 3.1 version.
Thanks,
Naveen
Naveen
-
- Premium Member
- Posts: 353
- Joined: Wed Apr 06, 2005 8:45 am
-
- Participant
- Posts: 232
- Joined: Sat May 07, 2005 2:49 pm
- Location: USA
-
- Premium Member
- Posts: 353
- Joined: Wed Apr 06, 2005 8:45 am